specifications of any and all sanyo semiconductor co.,l td. products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer ' s products or equipment. to verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer ' sproductsor equipment. any and all sanyo semiconductor co.,ltd. products described or contained herein are, with regard to "standard application", intended for the use as general electronics equipment (home appliances, av equipment, communication device, office equipment, industrial equ ipment etc.). the products mentioned herein shall not be intended for use for any "special application" (medica l equipment whose purpose is to sustain life, aerospace instrument, nuclear control device, burning appliances, t ransportation machine, traffic signal system, safety equipment etc.) that shall require extremely high level of re liability and can directly threaten human lives in case of failure or malfunction of the product or may cause har m to human bodies, nor shall they grant any guarantee thereof. if you should intend to use our products for app lications outside the standard applications of our customer who is considering such use and/or outside the scope of our intended standard applications, please consult with us prior to the intended use. if there is n o consultation or inquiry before the intended use, our customer shall be solely responsible for the use. o0808 ms jk/92900rm (ot) no.6631-1/8 LA4625 overview the LA4625 is a 2-channel general-purpos e btl audio power amplifier provided in a miniature package. it was designed for the best possible audio quality and features an extended lo w band roll-off frequency provided by a newly-developed nf circuit that does not require an external capacitor. furtherm ore, crosstalk, which can cause muddiness in the audio output, has been significantly reduced by both circuit and wiring pa ttern improvements. thus this amplifier can provide powerful lows and clear highs. note that this device is pin compatible with the 20w2-ch annel la4628, and allows end products differentiated by their power rating to share the same printed circuit board. features ? total output : 13.5w + 13.5w (at v cc = 12v, r l = 4 ? , thd = 10%) ? pmpo reference data : 115w2 (v cc = 20v, r l = 4 ? ) ? high-fidelity design (f l < 10hz, f h = 130khz) ? extremely low impulse noise levels ? an arbitrary amplifier startup time can be set up with external components. ? full complement of built-in protection circuits (includes circuits that protect against shorting to v cc , shorting to ground, load shorting, overvoltages and excessive temperatures) specifications maximum ratings at ta = 25 c parameter symbol conditions ratings unit maximum supply voltage v cc max no signal 24 v maximum output current i o peak per channel 3.5 a allowable power dissipation pd max with an arbitrarily large heat sink 32.5 w operating temperature topr -20 to +85 c storage temperature tstg -40 to +150 c orderin g number : en6631a monolithic linear ic 2-channel 13.5w btl audio power amplifier
LA4625 no.6631-2/8 operating conditions at ta = 25 c parameter symbol conditions ratings unit recommended supply voltage v cc 12 v recommended load resistance range r l op 4 to 8 ? allowable operating supply voltage v cc op 7.2 to 20 v note : with v cc , r l , and the output level in ranges such that th e pd max for the heat sink used is not exceeded. electrical characteristics at ta = 25c, v cc = 12v, r l = 4 ? , f = 1khz, rg = 600 ? ratings parameter symbol conditions min typ max unit quiescent current i cco rg = 0 65 120 240 ma standby mode current drain i st standby mode (amplifier off), with no power supply capacitor. 10 60 a voltage gain v g v o = 0dbm 38 40 42 db total harmonic distortion thd p o = 1w, filter = flat 0.06 0.2 % output power p o 1 thd = 10% 10 13.5 w output offset voltage v n offset rg = 0 -300 +300 mv output noise voltage v no rg = 0, bpf = 20hz to 20khz 0.1 0.5 mv ripple rejection ratio svrr rg = 0, v r = 0dbm, f r = 100hz 40 50 db channel separation chsep rg = 10k ? , v o = 0dbm 50 60 db input resistance ri 21 30 39 k ? standby pin applied voltage v st amplifier on (applied through an external 10k ? resistor) 2.5 v cc v package dimensions unit : mm (typ) 3113b 0 pd max -- ta -20 35 25 30 15 20 10 5 200 40 60 80 100 120 140 160 f = 3?c/w f = 4?c/w f = 7?c/w jc = 2?c/w ? fin f = 10?c/w 32.5 20.83 13.9 10.4 3.1 infinite heat sink allowable power dissipation, pd max -- w ambient temperature, ta -- ?c ai heat sink mounting torque 39n ? cm flat washer silicone grease applied
LA4625 no.6631-3/8 block diagram 0.1 f 0.1 f r4 c9** c8** r5 2.2? 2.2? r l 4? r l 4? -out2 +out2 ? + standby sw off ripple filter + bias circuit standby sw pop noise prevention circuit predriver predriver power power load short protector output pin to v cc short protector output pin to v cc short protector output pin to gnd short protector output pin to gnd short protector predriver predriver power power over voltage / surge protector thermal shut down load short protector v cc + + on r1 10k? +5v c4 2.2 f 10v 33 f 10v 0.47 f 10v 2.2 f 10v c1 100 f/16v v cc c5 2200 f 25v + -out1 +out1 ? + power gnd2 + + c3 c10 ** (polyester film capacitor) + ? in c2 pre gnd in2 c3 c10 sets the amplifier starting time (approximately 0.6 seconds when 33f) impulse noise reduction (note : the device?s ability to withstand shorting to v cc or shorting to ground when v cc is around 16v may be reduced as the value of this capacitor is increased. we recommend 0.47f.) power gnd1 14 2 1 3 4 6 7 5 11 12 13 0.1 f 0.1 f r2 c7** c6** r3 2.2? 2.2? 9 10 8 + ? in
LA4625 no.6631-4/8 pin voltages v cc = 12v, with 5v applied to stby through a 10k ? resistor, r l = 4 ? , rg = 0 pin no. 1 2 3 4 5 6 7 pin name in1 dc pre-gnd stby on time in2 pop pin voltage 1.46v 5.18v 0v 3.21v 2.26v 1.46v 2.05v pin no. 8 9 10 11 12 13 14 pin name + out2 ? out2 pwr-gn + out1 pwr-gn ? out1 v cc pin voltage 5.21v 5.21v 0v 5.21v 0v 5.21v 12v external components c1 and c4: input capacitors. a value of 2.2 f is recommended. determine the polarity based on the dc potential of the circuit connected directly to the LA4625 front end. note that the low band response can be adjusted by varying f l with the capacitors c1 and c4. c2 : decoupling capacitor (ripple filter) c3 : sets the amplifier starting time, which will be approximately 0.6 seconds for a value of 33 f. the starting time is proportional to the value of this capacitor, and can be set to any desired value. c5 : power-supply capacitor c6, c7, c8, and c9 : oscillation prevention capacitors. use polyester film capacitors (mylar capacitors) with excellent characteristics. (note that the series resistors r2, r3, r4, and r5 are used in conjunction with these capacitors to achieve stable ampl ifier operation.) a value of 0.1 f is recommended. c10 : impulse noise reduction capacitor. a value of 0.47 f is recommended. caution is required when selecting the value for this capacitor, since increasing its value influences the operation of the circuits that protect against shorting the amplifier output pins to v cc or to ground when higher v cc voltages (approximately 16v or higher) are used. r1 : standby switch current limiting resistor. a value of 10k ? is recommended when a voltage in the range 2.5 to 12v will be applied as the standby switching voltage. note that this resistor is not optional: it must be included. ic internal characteristics and notes 1. standby function ? pin 4 is the standby switch. a voltage of 2.5v or higher must be applied through an external resistor to turn the amplifier on. ? if a voltage of over 12v will be applied as the standby mode switching voltage, use the following formula to determine the value of r1 so that the current entering at pin 4 remains under 500 a. < applied voltage > ? 1.4 r1 = 500 a ? 10k ? 2. muting function ? pin 5 connects the capacitor that determines the starting tim e to prevent impulse noise. it can also be used to mute the amplifier output by shorting pin 5 to ground. when this function is used, the recovery time depends on c3. 3. impulse noise improvements ? while the LA4625 achieves a low level of impulse noise, if even further reductions in impulse noise at power on/off (and when switching into or out of standby mode) a 0.47 f capacitor may be inserted between pin 7 and the pre gnd pin (pin 3). (pin 7 is the output amplifier bias pin. since the ability to withstand shorting the output pins to v cc or ground is reduced for supply voltages over 16v if the pin 7 capacitance is large, we recommend a value of 0.47 f or lower for this capacitor.) 4 r1 10k? 500 a or lower about 1.4v (2v be ) pin 4 internal equivalent circuit applied standby voltage
LA4625 no.6631-5/8 4. protection circuits ? due to the system structure of the protection circuit for shorts to v cc or ground, if there is a dc resistance between the amplifier output pins and ground, the protec tion circuit may operate when power is first applied and the amplifier may fail to turn on. the basic design approach we recommend is not to adopt any designs in which there is a dc resistance between the amplifier outputs and ground. ? the LA4625 includes a built-in thermal protection circuit to prevent the ic from being damaged or destroyed if abnormally high temperatures occur. this thermal protec tion circuit gradually reduces the output if the ic junction temperature (tj) r eaches the range 170 to 180 c due to inadequate heat sinking or other problem. if the temperature falls, the amplifier will restart automatically. ? the LA4625 also includes other protection circuits. use of these circuits also requires care during end product design and testing. 5. other notes ? the LA4625 is a btl power amplifier. when testing this device, the ground systems for the test equipment connected to ic inputs, and that for the test equipment connected to ic outputs, must be isolated. do not use a common ground. printed circuit pattern (copper foil side)
LA4625 no.6631-6/8 thd = 30% 10% p o -- v cc 6 0 10 20 30 40 50 60 7 8 9 101112131415161718 f = 1khz rg = 600? r l = 4? 10khz 100khz 1khz thd -- p o 2 0.1 0.01 3 2 7 5 1.0 3 2 7 5 10 3 2 7 5 35 1.0 0.1 7235 10 7235 100 7 v cc = 12v r l = 4 ? rg = 600? thd -- f 2 0.1 0.01 3 2 7 5 1.0 3 2 7 5 10 3 2 7 5 35 100 10 7235 1k 7235 10k 7235 100k 7 v cc = 12v r l = 4 ? p o = 1w v no -- rg 2 0.1 0.01 3 2 7 5 1.0 3 2 7 5 35 1k 100 7235 10k 7235 100k 7 v cc = 12v r l = 4? p o -- v in 23 57 0.01 0.1 2 3 5 7 1.0 2 3 5 7 10 2 3 5 7 100 2 3 5 7 1.0 10 23 57 100 23 57 1k v cc = 12v r l = 4? f = 1khz thd = 10% thd = 3% thd = 1% p o -- f 23 57 0 4 8 12 16 20 24 10 100 23 57 1k 23 57 10k 23 57 100k v cc = 12v r l = 4 ? rg = 600? f response 23 57 -10 -8 -6 -4 -2 0 2 10 100 23 57 1k 23 57 10k 23 57 100k v o = 0dbm at f = 1khz chsep -- f 90 80 70 60 50 40 30 20 10 0 23 7 5 100 10 23 7 5 1k 23 7 5 10k 23 7 5 100k v cc = 12v r l = 4? rg = 10k? v o = 0dbm v cc = 12v r l = 4? rg = 600? output power, p o -- w supply voltage, v cc -- v output power, p o -- w total harmonic distortion, thd -- % frequency, f -- hz total harmonic distortion, thd -- % signal source resistance, rg -- ? output noise voltage, v no -- mvrms input voltage, v in -- mvrms output power, p o -- w frequency, f -- hz output power, p o -- w frequency, f -- hz response -- db frequency, f -- hz channel separation, chsep -- db ch1 2 ch2 1
LA4625 no.6631-7/8 out2 out1 svrr -- v cc 4 -120 -100 -80 -60 -40 -20 0 6 7 8 10121416182022 rg = 0 f r = 100hz v ccr = 0dbm v n -- v cc 0 5 10 15 20 25 30 35 0 2 4 6 8 10 12 r l = 4? rg = 0 v n -- v out1 out2 svrr -- f r 23 57 -100 -80 -60 -40 -20 0 10 100 23 57 1k 23 57 10k 23 57 100k v cc = 12v v ccr = 0dbm r l = 4? rg = 0 i cco -- v cc 0 4 8 12162024283236 0 20 40 60 80 100 120 140 160 180 r l = open rg = 0 pd, i cc -- p o 2 10 1.0 3 2 7 5 100 3 2 7 5 1.0 3 2 7 5 10 3 2 7 5 35 1.0 0.1 7235 10 7235 100 7 r l = 4? rg = 600? f = 1khz v cc = 15v i cc v cc = 12v amp on time 0 0.2 0.4 0.6 0.8 1.0 23 57 1.0 10 23 57 100 c3 -- f v cc = 12v v st = 5v amp on time -- s 100hz out1 3khz out1 3khz out2 svrr = 20log v o v ccr 100hz out2 svrr -- v ccr 0 -100 -80 -60 -40 -20 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 v cc = 12v r l = 4? 0.1 ripple rejection ratio, svrr -- db supply voltage, v cc -- v ripple frequency, f r -- hz ripple rejection ratio, svrr -- db supply voltage, v cc -- v quiescent current, i cco -- ma output power, p o -- w/ch power dissipation, pd -- w power dissipation, i cc -- a ripple rejection ratio, svrr -- db power supply ripple, v ccr -- vrms supply voltage, v cc -- v
LA4625 ps no.6631-8/8 sanyo semiconductor co.,ltd. assumes no responsib ility for equipment failures that result from using products at values that exceed, even momentarily, rate d values (such as maximum ra tings, operating condition ranges, or other parameters) listed in products specif ications of any and all sanyo semiconductor co.,ltd. products described or contained herein. sanyo semiconductor co.,ltd. strives to supply high-qual ity high-reliability products, however, any and all semiconductor products fail or malfunction with some probability. it is possible that these probabilistic failures or malfunction could give rise to acci dents or events that could endanger human lives, trouble that could give rise to smoke or fire, or accidents that could cause dam age to other property. when designing equipment, adopt safety measures so that these kinds of accidents or e vents cannot occur. such measures include but are not limited to protective circuits and error prevention c ircuits for safe design, redundant design, and structural design. upon using the technical information or products descri bed herein, neither warranty nor license shall be granted with regard to intellectual property rights or any other rights of sanyo semiconductor co.,ltd. or any third party. sanyo semiconductor co.,ltd. shall not be liable f or any claim or suits with regard to a third party's intellctual property rights which has resulted from the use of the technical information and products mentioned above. information (including circuit diagr ams and circuit parameters) herein is for example only; it is not guaranteed for volume production. any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. when designing equi pment, refer to the "delivery specification" for the sanyo semiconductor co.,ltd. product that you intend to use. in the event that any or all sanyo semiconductor c o.,ltd. products described or contained herein are controlled under any of applicable local export control laws and regulations, such products may require the export license from the authorities conc erned in accordance with the above law. no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any in formation storage or retrieval system, or otherwise, without the prior written consent of sanyo semiconductor co.,ltd. this catalog provides information as of october, 2008. specifications and information herein are subject to change without notice.
|
